Power specifications EIA output power (1 kHz, THD 1%) Both channels 8 ohms: 650W + 650W 4 ohms: 1.100W + 1.100W 8 ohms bridged: 2.200W Electrical specifications Input sensitivity 0dB (0.775V) Input impedance 10 kohms (balanced) Frequency response 10Hz - 50kHz (-0,5dB) Voltage gain 39 dB Slew rate 22 V/ms Damping factor Higher then 400:1 @ 1kHz, 8 ohms Crosstalk -82dB (1kHz) S/N ratio -98dB Harmonic distorsion (THD) Lower then 0,1% (ref 20Hz -20kHz) Intermodulation distortion SMPTE Lower then 0,1% (SMPTE method, 60Hz & 7kHz, 400:1 ratio) General specifications Protections Power transformer thermal protection; short circuit protection; sensor for current on outputs; clip limiter on each channel; soft-start circuit (1000P to 2200P) Controls On/off switch, 21-detect input level control for each channel, Mode selector, Shield selector Indicators Power On: 1 red LED Bridge: 1 red LED Protect: 1 red LED Level: 2 x 5 LED meter Limit: 1 red LED Connections Input: 1 XLR-F + 1 1/4' jack in parallel for each channel Output: 2 binding post + 1 speakon for each channel (400-1500); 1 speakon for each channel + 1 speakon for Bridge output (1800-2200) Power supply See label on the apparatus Dimensions (W x H x D) 483 x 88 x 456 mm / 19' x 3,46' x 17,95' Weight 25 kg / 55,1 lbs

DX 1500, Dual-Channel Power Amp from Hill Audio Ltd. Pojacalo je ispravno. Nikada nije popravljano. SPECIFICATIONS •Size 19" rack mount, 3-1/2" high (2 rack spaces) •13" behind back panel •Weight 34 lbs (15Kg) •AC Supply 50/60Hz 240/220 VAC - 5 amps - music power •240/220 VAC - 10 amps - full power sine wave 120/110 VAC - 10 amps - music power •120/110 VAC - 20 amps - full power sine wave •The supply voltage is NOT switchable, so verify the voltage of your amplifier

U odlicnom stanju..pojacalo za kola..

telefunken linija iz tri komponente

sanyo sistem od tri komponente

povoljno resiver sony

Risiver proizveden 1978 godine. Težak 15 kg! Ispravan, dek prima sve komande ali neokreće kasetu, verovatno gumica. Na levom poklopcu za komande treba pomoć rukom za otvaranje. Desni ok.

Code: 39694 Both channel driven 8 ohm 1% THD Continous/impulsive: 230/250 Both channel driven 4 ohm 1% THD Continous/impulsive: 350/400 Bridge 8ohm 1% THD: 700/800 Input impedance: 20Kbalanced Signal to noise ratio S/N: >100dB Total harmonic dist. (1kHz-4ohm): < 0.03% Frequency response: 20Hz-40kHz -6dB Damping Factor: > 400 Class: AB Maximum power consuption: 1000VA Power supply voltage: 120 or 230 Vac 50/60Hz Protections: Short circuit / thermal Connectors: IN: XLR/Jack - Out: Speakon/Binding post Net Dimensions (WxHxD): 482x88x290 / 19x3.5x11.4

MA 1300 Professional Power Amplifier Description The MA Series professional power amplifiers offer Martin Wisman renowned integrity and can handle exceptionally high power ratings in a compact, light weight 2RU package. The MA Series amps also feature Automatic Clip Limiting to protect connected drivers; Impedance sensing to accommodate varying impedance outputs; tunnel cooled, high efficiency heat sinks; and variable speed DC fans to limit the operating temperature and extend amplifier life. Individual low pass, low cut switch for channel A and B. Specifications Rated power bridge mode 4 Ohms: 1350 Watts @ 1 kHz at <0.1% T.H.D. Rated power (2 X 2 Ohms): 675 Watts per channel @ 1 kHz at <0.1% T.H.D.both channels driven Rated power (2 X4 Ohms): 450 Watts per channel @ 1 kHz at <0.05% T.H.D. both channels driven Rated power (2 X 8 Ohms): 300 Watts per channel @ 1 kHz at <0.025% T.H.D.both channels driven Rated power (1 X 2 Ohms): 750 Watts @ 1 kHz at <0.1% T.H.D. Power bandwidth: 10 Hz - 30kHz; +0, -3 dB at rated 200 Watts 8 Ohm power T.H.D.(2 X 2 Ohms): <0.1%@500 Watts per channel from 20 HZ to 20 kHz T.H.D.(2 X 4 Ohms): <0.1%@350 Watts per channel from 20 HZ to 20 kHz T.H.D.(2 X 8 Ohms): <0.1%@250 Watts per channel from 20 HZ to 20 kHz Minimum load impedance: 2 Ohms Maximum RMS voltage swing: 53 Volts Frequency response: 10 Hz - 100 kHz; +0, -3 dB at 1 Watt Input CMRR: >-65 dB @ 1 kHz Rated power (1 X 4 Ohms): 500 Watts @ 1 kHz at <0.05% T.H.D. Rated power (1 X 8 Ohms): 330 Watts @ 1 kHz at <0.025% T.H.D. Phase response: +5 to -15 from 20 Hz to 20 kHz Input impedance: 20 k Ohms, balanced; 10k Ohms, unbalanced Cooling: Two temperature dependant variable speed 80mm high output DC fans Controls: Two front panel attenuators, rear panel mode switch and gain select switch Voltage gain: 0.775V, 32 dB or 26 dB Crosstalk: >-60 dB @ 1 kHz at rated power @ 8 Ohms Hum and noise: >-105 dB, "A" weighted referenced to rated power @ 8 Ohms Slew rate: >30V/us Damping factor (8 Ohms): >500:1 @ 20Hz - 1 kHz Indicator LEDs: 2 Clip,2 signal presence, 1 active status,2 Protection Protection: Thermal, DC, turn-on bursts, subsonic, incorrect loads Connectors: XLR, Speakon and Binding Post speaker output, 240/230 Volt 16 amp IEC mains Construction: 16 ga. Steel Dimensions: 89 mm x 483 mm x 496 mm Net weight: 18kg Gross weight: 21kg

Description Carvin DCM1500-E 2 x 500 Watt 4 Ohm 2 x 300 Watt 8 Ohm 2 x 750 Watt / 2 Ohm Bridged Mode: 1 x 1500 Watt / 4 Ohm 1 x 1000 W / 8 ohms Frequency response: ± 0.5 dB, 20 Hz tp 20kHz ± 1.5dB. 10 Hz & 40kHz THD: (50% of the capacity of 0.03%) (20-20k Hz, 0.1 % @ 90%) Damping factor:> 500 Size: 2 U Weight: 15,30 kg

PRODUCT DESCRIPTION 2 Ch. Power Amp - 2x600Wrms (4ohm) - 1200Wrms (8ohm bridge) Suitable applications: Amplification for live sound reinforcement speaker systems in clubs, discos, piano bar, conference halls, houses of worship, sports arenas, schools, theatres, mobile D.J. use, recording studio monitors, foreground music reproduction, etc. Tour tough built, sleek design, impressive specs, excellent cost per watt performance, efficient under any application. With these credentials, FBT proudly presents the new AX series of power amplifiers, the perfect power mates for sound reinforcement speaker systems. The AX series consists in four 2HU rack mount models, from 800 to 3000 watts, all designed with sophisticated power amp circuits for improved quality, stability and reliability, all equipped with Stereo-Parallel-Bridge operation mode, dB sensitivity switch (26-29-32dB), limiter, ground lift, XLR/Jack inputs (plus extra RCA input on AX 800), Speakon/Binding posts outputs. KEY FEATURES Both channel driven 8 ohm 1% THD Continous/impulsive: 340/350W Both channel driven 4 ohm 1% THD Continous/impulsive: 460/600W Bridge 8ohm 1% THD: 920/1200W Input impedance: 20K balanced Signal to noise ratio S/N: >100dB Total harmonic dist. (1kHz-4ohm): < 0.03% Frequency response: 20Hz-40Khz -6dB Damping Factor: > 400 Class: H - 2 step Maximum power consuption: 1300VA Power supply voltage: 120 or 230 Vac 50/60Hz Protections: Short circuit / thermal Cooling: in: XLR/Jack out: Speakon/Binding oist Net Dimension (WxHxD): 482 x 88 x 290mm

Harmanovo pojačalo pravljeno za američko tržište, koncipiran kao dual mono, sa dva torusna trafoa. Estetski odlično sačuvan, jedino što na frontu su blago izbledela slova, najviše sama oznaka Harman Kardon. Sve ostalo sasvim dobro vidljivo.

Tuning range: FM, MW Power output: 100 watts per channel into 6Ω (stereo) Surround output: 100W (front), 100W (center), 100W (rear) Frequency response: 20Hz to 50kHz Total harmonic distortion: 0.08% Damping factor: 60 Input sensitivity: 200mV (line) Signal to noise ratio: 100dB (line) Output: 200mV (line) Speaker load impedance: 6Ω to 16Ω Digital inputs: coaxial, optical Video Connections: HDMI, component, composite Dimensions: 435 x 151.5 x 328.5mm Weight: 8kg

TA 1KHz THD≤ 0.5% STEREO 8Ω 300W+300W 4Ω 450W+450W BRIDGE 8Ω 900W FREQUENCY RESPONSE 20Hz-20KHz ±0.5dB INPUT SENSITIVITY 1V (a-w rms) S/N RATIO 100dBA THD(typilcal) 0.10% (SMPTE) 0.10% Input impedance 20K OHMS(BALANCED) 10K OHMS(UN-BALANCED) (5Hz-1KHz) DAMPING FACTOR >200 PROTECTION SOFT START,DC,VHF,AC,SHORT CIRCUIT,LIMITER,OVER HEAT SLEW RATE 20V/US Connection NEUTRIK XLR:NEUTRIK SPEAKON HTINPUT VOLTAGE AC115-235V 50Hz-60Hz NET WEIG 2Kg (WXDXH)mm Dimensions 482×165×44mm

AX POWER AMPLIFIERS Tour tough built, sleek design, impressive specs, excellent cost per watt performance, efficient under any application. With these credentials, FBT proudly presents the new AX series of power amplifiers, the perfect power mates for sound reinforcement speaker systems. The AX series consists in four 2HU rack mount models, from 800 to 3000 watts, all designed with sophisticated power amp circuits for improved quality, stability and reliability, all equipped with Stereo-Parallel-Bridge operation mode, dB sensitivity switch (26-29-32dB), limiter, ground lift, XLR/Jack inputs (plus extra RCA input on AX 800), Speakon/Binding posts outputs. Both channel driven 8 ohm 1% THD Continous/impulsive: 880/650 Both channel driven 4 ohm 1% THD Continous/impulsive: 1300/1500 Bridge 8ohm 1% THD: 3600/3000 Input impedance: 20k balanced Signal to noise ratio S/N: >100dB Total harmonic dist. (1kHz-4ohm): <0.03% Frequency response: 20Hz - 40KHz -6dB Damping Factor: >230 Class: H-2 step Maximum power consuption: 3600VA Power supply voltage: 120 or 230 Vac 50/60 Hz Protections: short circuit /thermal Connectors: IN: XLR/Jack - OUT: Speakon Net Dimensions (WxHxD): 482x88x290 / 19x3.5x11.4

6-zone power amplifier Comfortable control of your PA speakers via 6-zone technology Fan-cooled 3 Mic and 3 Aux inputs 1 Line output 70 V, 100 V PA outputs 4-16 ohm output for connecting a passive speaker system 6 zone outputs 5-step volume control for every zone 1 Mic connection on the front panel with priority function Treble and bass control 7-fold level indicator Master control 19"" dimensions Protection-circuits: over current, short circuit, turn-on delay Technical specifications: Power supply:230 V AC, 50 Hz ~ Output power:250 W RMS Output type:70 V, 100 V or 4-16 W Output current: 70 V3.6 A 100 V2.5 A Mic input:5 mV, 600 Ohms Line input:300 mV, 10 kOhms Output-connectors:Screw connectors, terminal block Frequency range:80 Hz - 16 kHz Distortion:0.5 % (1 kHz) S/N-ratio: Aux:85 dB Mic:75 dB Dimensions:483 x 385 x 92 mm Weight:14 kg MPVZ 250 250W 3.6A 1.8A 1.8A 3.5A Frequency Response ±2dB @80Hzto 16KHz 0.5%(1KHz) 600 Q -60db 10KQ -10db 66dB 70dBn Oto-30dB USA:115V/60Hz Europe: 230VAC, 50Hz Weight: 14 kg WxDxH=480 X 380 X 88 (MM) WxDxH=560 X 480 X 190 (MM)

Product Features Four channels; 3 watts of continuous power per channel Burst mode to handle peak signals in accordance with ANSI/CTA-2006-B; supports up to 50 watts (4Ω load) or 30 watts (8Ω load) per channel Powered by PoE+ (IEEE 802.3at Class 4, 30W) RJ-45 connectors enable termination-free connections to compatible speakers like the Desono C-IC6 Class D amplifier topology Fanless operation BPAK accessory included Audible locate function available on the front panel Includes internal limiter function Software-selectable power versus channel count Evaluated to the requirements of UL 2043 and is suitable for use in air handling spaces Configurable via Tesira software CE marked, UL listed, and RoHS compliant Covered by Biamp Systems’ five-year warranty Product Specifications General Network Connection: RJ-45 with Ethernet cable (Cat 5e and above) Number of Channels: 4 Connectors: RJ-45 Amplifier Topology: Class D Burst Power Output (per ANSI/CTA-2006-B @ 1kHz): 4Ω (per channel): 50W 8Ω (per channel): 30W Continuous Power Output: Single Channel Driven (4Ω, 8Ω): 15W Dual Channel Driven, (4Ω, 8Ω): 7W Four Channel Driven, (4Ω, 8Ω): 3W THD+N (20Hz-20kHz, at continuous power): < 0.3% Frequency Response (20Hz-20kHz): ± 1dB Dynamic Range (20Hz-20kHz BW): > 90dB Minimum Operational Load: 4Ω Intermodulation distortion (SMPTE): <0.3% Cross Talk (channel to channel @ 1kHz): < -90dB Cooling: Convection Power: PoE+ (IEEE 802.3at Class 4 , 30W) Indicators: Power Indicator (Green/Yellow/Red LED) Amp Status Indicator (Green/Yellow/Red LED) Physical Dmensions: Height: 1.2 inches (30mm) Width: 7.7 inches (195mm) Depth: 4.7 inches (120mm) Weight: 1.5 lbs (0.7 kg) Environmental: Ambient Operating Temperature Range: 32 - 104° F (0 - 40° C) Humidity: 0-95% relative humidity (non-condensing) Altitude: 0-10,000 ft (0-3000m) MSL Compliance: FCC Part 15B (USA) UL and C-UL listed (USA and Canada) CE Marked (Europe) KCC (Korea) RoHS Directive (Europe) Evaluated to the requirements of UL 2043 and is suitable for use in air handling spaces

Output Power: 2500W @ 2 ohms per channel, 1800W @ 4 ohms per channel High-current toroidal transformers for greater two-ohm power and low noise Independent user-defeatable clip limiters reduce distortion XLR, 1/4” and barrier strip inputs all included Front mounted detented gain controls for easy access Bridge mono and parallel mode LEDs Fast Recovery design for lower distortion if clipping occurs Very rugged housing Active balanced inputs for low noise Signal level at -40, -20, -10, protect and clip LED indicators to monitor performance Ground Lift switch to prevent humming Selectable stereo, parallel & bridge mono amp modes Two ventilation variable speed fans Speakon-type connectors and 5-way binding posts speaker outputs XLR & 1/4" TRS connectors for maximum input flexibility Requires two standard rack units for mounting Fits a standard 19" rack

RMX 1450 The power supply is the heart of an amplifier, converting raw AC power from the wall to clean DC for the audio circuitry. The RMX uses a powerful high-current toroidal transformer and ample filter capacitance to ensure generous energy reserves. This makes a critical difference in sound quality, allowing the amp to effortlessly punch out high level transients, even when driving abusive 2-ohm speaker loads. Superior Performance RMX amplifiers deliver true studio-quality sound. A full complementary output circuit using the highest-grade linear output devices delivers ultra-low distortion (<0.05% THD) and a ruler-flat frequency response. SMT (Surface Mount Technology) triples small-signal component density, enabling us to pack up to 2400 watts of power in a chassis only 2 rack spaces and less than 16" deep. And unlike other designs, RMX output devices are direct-mounted to the heat sink for optimum thermal coupling and cooling. Features - Independent defeatable clip limiters reduce distortion without sacrificing peak performance. - Selectable low-frequency filters boost system response, protect speakers, and ensure low-end tightness by more precisely matching the amplifier's range to the loudspeakers. - Barrier strip, XLR, and 1/4" balanced inputs plus Speakon and binding post outputs provide easy connections. - Low-noise variable speed fans with rear-to-front air flow keep amplifiers and racks cool. SPECIFICATIONS RMX 1450 STEREO MODE (Both Channels Driven) 8 ohms FTC 20 Hz - 20 kHz, 0.1% THD EIA 1 kHz, 0.1% THD 260 W 280 W 4 ohms FTC 20 Hz - 20 kHz, 0.1% THD EIA 1 kHz, 0.1% THD 400 W 450 W 2 ohms EIA 1 kHz, 1% THD 700 W BRIDGE MONO MODE 8 ohms FTC 20 Hz - 20 kHz, 0.1% THD EIA 1 kHz, 0.1% THD 800 W 900 W 4 ohms EIA 1 kHz, 1% THD 1400 W Signal to Noise, 20 Hz-20 kHz 100 dB Distortion (SMPTE-IM) Less than 0.01% Input Sensitivity @ 8 ohms 1.15V (+3.4 dBu) Voltage Gain 40x (32 dB) Output Circuitry AB Power Requirements 1/8 power pink noise at 4 ohms * 6A ALL MODELS Distortion (Typical) 20 Hz - 20 kHz: 10 dB below rated power 1.0 kHz and below: full rated power Less than 0.03% THD, 4 and 8 ohms Less than 0.03% THD, 4 and 8 ohms Frequency Response 20 Hz-20 kHz, ±1 dB -3 dB points: 5 Hz - 50 kHz Damping Factor, 1 kHz and below Greater than 300 at 8 ohms Input Impedance 10k ohms unbalanced, 20k ohms balanced Input Clipping 10 Vrms (+22 dB) Cooling Continuously variable-speed fan, rear-to-front air flow Connectors, each channel Input: Active balanced; barrier strip, XLR and 1/4" (6.3mm) TRS tip and XLR (pin 2 positive) Output: touch-proof binding posts and Neutrik® Speakon® Controls Front: AC switch, Ch. 1 and Ch. 2 gain knobs Rear: 10-position DIP switch Indicators Power-On: Green LED Signal: Yellow LED (1 per channel) Clip: Red LED (1 per channel) Amplifier Protection Stable into reactive or mismatched loads Load Protection On/off muting, AC coupling (850, 1450), triac crowbar (1850HD, 2450, on each channel) Power Requirements 100, 120, 230 VAC, 50-60 Hz Dimensions 19" (48.3 cm) rack mounting, 3.5" (8.9 cm) tall (2 RU), 15.9" (40 cm) deep (rack mounting to rear support ears)

REVAMP4240T is the ideal amplifier for applications with 4 zones in mono, 2 zones in stereo or even bridged dual mono or bridged stereo systems. This amplifier contains an intelligent variable speed cooling fan that only will be activated in case of emergency. In order to match each input to its respective source the input sensitivity can be adapted to your needs. The input stage also features a build-in 250 Hz HP-filter to optimise the system for use on horn speakers whenever you would need this. Each pair of outputs can be bridged to give you 2 x 480 watts of output power! The very intuitive front display shows what is going on with one blink of an eye. The output power is constantly under control thanks to our own made limiter that prevents annoying pumping limiter sound but yet keeps the system fully under control and you still have that dynamic sound. Ease of use, high-tech, reliability and a wide versatility has never been as cleverly combined as in this REVAMP4240T amplifier. dynamic output power 4 ohms 4 x 240 watts RMS output power 4 ohms 4 x 240 watts dynamic output power 8 ohms 4 x 120 watts RMS output power 8 ohms 4 x 120 watts dynamic output power bridged 8 ohms 2 x 480 watts output power RMS bridged 8 ohms 2 x 480 watts output power RMS 100 volts 4 x 240 watts output power RMS bridged 100 volts 2 x 480 watts minimum impedance load per channel 4 ohms minimum impedance load bridged per channel 8 ohms power consumption (max) 1050 watts 19" (483 mm wide) rack mounting Yes height- rack units (1U=44 mm) 2 U depth (build in) 330 mm depth (incl front) 338 mm power supply 115 - 230 VAC volts Power supply technology 2 x switching mode power supply output voltage tappings 100 - 70 - 50 - 35 - 4 Ohm watts output channels 4 line input balanced 4 line input unbalanced 4 Channel separation > 68 dB @ 1 kHz Power amp topology Class-D frequency response (in Hz) 50 - 20K cooling system fan applicable in 100V Yes applicable low impedance Yes Net weight product (kg)

Specifikacija Stereo 4 ohm: 2x 170W Stereo 8 ohm: 2x 100W Stereo 2 ohm: 2x 200W Bridge 8 ohm: 215W Bridge 4 ohm: 400W Frekvencijski odziv: 20 Hz a 20 kHz < +/- 0.5dB Distorzija: < 0.1 % (1 kHz) Ulaz izolacija: 10 - 20 kohm balansirano Signal / sum: < 95 dB Tezina: 7.5 kg Napajanje: 230V / 50Hz Dimenzije: 480 x 410 x 88 (19"/2U)

Features Fan-cooled 3 Mic and 3 Aux inputs 1 Line-output 70 V, 100 V PA-outputs 4-16 Ohms output for connecting a passive speaker-system for monitor 1 Mic-connection on the front panel, Chime button Build in Mp3 player with songs name display Treble and bass control 7-fold level indicator Master-control 19"-dimensions Protection-circuits: over current, short circuit, turn-on delay Screw terminals of 6 zone outputs Specifications MODEL TPU-3060 TPU-3120 TPU-3180 Z6 TPU-3250 TPU-3250 Z6 Power supply AC110V~ 60 Hz AC110V~ 60 Hz AC110V~ 60 Hz AC110V~ 60 Hz AC110V~ 60 Hz Output power 60W RMS 120W RMS 180 W RMS 250 W RMS 350 W RMS Output type 70 V, 100 V or 4-16 70 V, 100 V or 4-16 70 V, 100 V or 4-16 70 V, 100 V or 4-16 70 V, 100 V or 4-16 Outputcurrent at 70V 0.9A 1.4A 2.5 A 3.6 A 5.0A Output current at 100 V 0.6A 1.0A 1.8 A 2.5 A 3.5A Mic input 5 mV, 600 Ohms 5 mV, 600 Ohms 5 mV, 600 Ohms 5 mV, 600 Ohms 5 mV, 600 Ohms Line input 300 mV, 10 kOhms 300 mV, 10 kOhms 300 mV, 10 kOhms 300 mV, 10 kOhms 300 mV, 10 kOhms Frequency range 80 Hz - 16 kHz 80 Hz - 16 kHz 80 Hz - 16 kHz 80 Hz - 16 kHz 80 Hz - 16 kHz Distortion 0.5 % (1 kHz) 0.5 % (1 kHz) 0.5 % (1 kHz) 0.5 % (1 kHz) 0.5 0.5 % (1 kHz) 0.5 Signal/Noise ratio: Aux 85 dB 85 dB 85 dB 85 dB 85 dB Mic 75 dB 75 dB 75 dB 75 dB 75 dB FUSE T2A/250V T2A/250V T2A/250V T5A/250V T5A/250V Carton dimensions 535X375X175mm 550X425X180mm 550X425X180mm 550X455X180mm 550X455X180mm Weight 9.25kg 11kg 12 kg 14 kg 16 kg

The revolutionary Apart MA120 mixing amplifier offers the end-user an unseen cutting-edge design and ease-of-use. The ground-breaking intuitive front panel is clear and easy to use without any unnecessary bells and whistles. The volume control rotary on the front panel is prominent, illuminated, bigger and put in the forefront while the mic volume control is smaller and recessed. The unit offers 120 watts in 70 or 100 volt mode and comes with two mic/line inputs and four stereo line, mono summed inputs. The refreshing rear panel will give every installer an instant gratification due to the sheer and logic design. Together with an unprecedented connectivity and immaculate sound performance these reliable mixing amplifiers will conquer the fixed-install audio market. 19" (483 mm wide) rack mounting yes height- rack units (1U=44 mm) 2 U depth (build in) 290 mm depth (incl front) 300 mm power supply 100 - 240 VAC power consumption (max) 160 watts output power RMS 100 volts 120 watts output power RMS 4 ohms 120 watts dynamic output power 100 volts 120 watts minimum impedance load 4 ohms output power tappings 70 - 100 volts - 4 ohms zone outputs 1 MIC inputs balanced 3 inputs with Phantom power 2 line input unbalanced 4 tone control yes priority switch 2 VOX mute yes chime yes emergency input 1 priority output 1 priority levels 4 power amp topology class-D frequency response (in Hz) 60 - 20 k cooling system convection applicable in 100V yes applicable low impedance yes Net weight product (kg) 5

-Professional 4-channel power amplifier in an extremely compact 19" 1U-housing (H: 44mm) -The unit houses 2 separate class-D amplifiers that can be configured independently to obtain the following combinations: Both amps in stereo mode: 4x 200Wrms @ 4Ω (4x 100Wrms @ 8Ω) Both amps in mono mode: 4x 200Wrms @ 4Ω (4x 100Wrms @ 8Ω) Both amps in Bridge mode: 2x 400Wrms @ 8Ω 3 Channel mode (2 sattelites + sub): 2x 200Wrms @ 4Ω (or 2x 100Wrms @ 8Ω) + 1x 400Wrms @ 8Ω -120Hz High Pass Filter on/off switch for satellite speakers -120Hz Low Pass Filter on/off switch for subwoofer -DC fault + high temperature + overload and short circuit protections -A plastic cover (included) can be installed to prevent access to the level knobs -Balanced XLR inputs -Speakon® compatible outputs General : Dimensions (cm) 48.3 x 4.4 x 24 General : Weight (kg) 4.71 General : Color black General : Powerinput AC 230V, 50Hz General : Energy Label No General : Display No General : RU 1U General : IP rating indoor Audio : min. frequency (Hz) 20 Audio : max. frequency (Hz) 20000 Audio : frequency range 120 Audio : S/N ratio (> dB) 100 Audio : max. output channels 4 Audio : Wrms 4Ω stereo, per channel 200 Audio : Wrms 8Ω stereo, per channel 100 Audio : Wrms 8Ω bridge 400 Audio : functions fixed crossover Connections : input 3 pin XLR, IEC Connections : output speakon

TA 1KHz THD≤ 0.5% STEREO 8Ω 100W+100W 4Ω 200W+200W BRIDGE 8Ω 300W FREQUENCY RESPONSE 20Hz-20KHz ±0.5dB INPUT SENSITIVITY 1V (a-w rms) S/N RATIO 100dBA THD(typilcal) 0.10% (SMPTE) 0.10% Input impedance 20K OHMS(BALANCED) 10K OHMS(UN-BALANCED) (5Hz-1KHz) DAMPING FACTOR >200 PROTECTION SOFT START,DC,VHF,AC,SHORT CIRCUIT,LIMITER,OVER HEAT SLEW RATE 20V/US Connection NEUTRIK XLR:NEUTRIK SPEAKON HTINPUT VOLTAGE AC115-235V 50Hz-60Hz NET WEIG 2Kg (WXDXH)mm Dimensions 482×165×44mm